Batgirl 3D print
Moderators: Scott Sebring, Ben Bentley
Forum rules
You must read the MERCHANDISE RULES before participating here.
You must read the MERCHANDISE RULES before participating here.
- SketchCardsAndCovers
- Posts: 2
- Joined: Fri Jul 03, 2020 8:36 am
Batgirl 3D print
I just finished printing my model of Batgirl!
I had a couple of minor failures.
The belt and the things sticking off her gloves are a bit too thin and some pulled off with the supports so I'm going to thicken them up a bit.
but seriously I can't believe the eyelashes printed perfectly!!
...haven't printed the base yet so I stuck her in some clay to stand her upright.
print is 8 inches tall.
I think I'm going to separate the boots from the legs in the next print
I had a couple of minor failures.
The belt and the things sticking off her gloves are a bit too thin and some pulled off with the supports so I'm going to thicken them up a bit.
but seriously I can't believe the eyelashes printed perfectly!!
...haven't printed the base yet so I stuck her in some clay to stand her upright.
print is 8 inches tall.
I think I'm going to separate the boots from the legs in the next print
- Jimmy L. 66
- Posts: 0
- Joined: Mon Nov 24, 2014 5:45 pm
Re: Batgirl 3D print
Very nice job. Do you sculpt this yourself, or find it online?
- Ben Bentley
- Moderator
- Posts: 1282
- Joined: Fri Aug 17, 2012 2:31 pm
Re: Batgirl 3D print
I really like this stylized version you've come up with! I can only imagine that these would be really popular if you made them available like your trading cards.
Re: Batgirl 3D print
I know that I'd like to buy one..."If the Price is Right"!!!!Ben Bentley wrote: ↑Mon Mar 27, 2023 4:55 pm I really like this stylized version you've come up with! I can only imagine that these would be really popular if you made them available like your trading cards.
Larry
- SketchCardsAndCovers
- Posts: 2
- Joined: Fri Jul 03, 2020 8:36 am
- SketchCardsAndCovers
- Posts: 2
- Joined: Fri Jul 03, 2020 8:36 am
Re: Batgirl 3D print
I did. Thank you! It was built in Lightwave.
Jimmy L. 66 wrote: ↑Sun Mar 26, 2023 10:22 pm Very nice job. Do you sculpt this yourself, or find it online?
- SketchCardsAndCovers
- Posts: 2
- Joined: Fri Jul 03, 2020 8:36 am
Re: Batgirl 3D print
Thank you! It's a possibility, but my model painting is pretty weak. I couldn't do anything till I get much much better.
Ben Bentley wrote: ↑Mon Mar 27, 2023 4:55 pm I really like this stylized version you've come up with! I can only imagine that these would be really popular if you made them available like your trading cards.
- SketchCardsAndCovers
- Posts: 2
- Joined: Fri Jul 03, 2020 8:36 am
- SketchCardsAndCovers
- Posts: 2
- Joined: Fri Jul 03, 2020 8:36 am
Re: Batgirl 3D print
My intention was to do that " posted in merchandise" but after painting the model I realized I was pretty bad at painting on a non-flat surface.
Completely different skill set than drawing on paper.
However, if you're someone who likes painting models... I could offer a kit. all the parts and the logo base plus, since printing the first one I've removed the chest logo and I print it as a separate piece so that will make painting much easier.
Completely different skill set than drawing on paper.
However, if you're someone who likes painting models... I could offer a kit. all the parts and the logo base plus, since printing the first one I've removed the chest logo and I print it as a separate piece so that will make painting much easier.
Larry A. wrote: ↑Tue Mar 28, 2023 2:51 pmI know that I'd like to buy one..."If the Price is Right"!!!!Ben Bentley wrote: ↑Mon Mar 27, 2023 4:55 pm I really like this stylized version you've come up with! I can only imagine that these would be really popular if you made them available like your trading cards.
- SketchCardsAndCovers
- Posts: 2
- Joined: Fri Jul 03, 2020 8:36 am
Re: Batgirl 3D print
Finished piece! looks perfect... from 4 feet away.
Eyelashes are a female dog! I had no idea how much my hand shakes. or that I would ever need a 3 hair brush!
You may also notice the thingies "Is it Scallops?" on her gloves broke off when I removed the supports, so since then I thickened them up a good bit.
Eyelashes are a female dog! I had no idea how much my hand shakes. or that I would ever need a 3 hair brush!
You may also notice the thingies "Is it Scallops?" on her gloves broke off when I removed the supports, so since then I thickened them up a good bit.
Re: Batgirl 3D print
Those are great. I'm in. Actually if the stl's were available that would be preferred.
Saving up for an Elegoo Mars possibly Saturn resin printer. Be nice to print off the scale
I have a call for. Either way.
A series of "toonies" would awesome. As well as the 66 Batman series, there would most likely
be an interest in the Green Hornet, Kato and George Reeves Superman. Just sayin
Saving up for an Elegoo Mars possibly Saturn resin printer. Be nice to print off the scale
I have a call for. Either way.
A series of "toonies" would awesome. As well as the 66 Batman series, there would most likely
be an interest in the Green Hornet, Kato and George Reeves Superman. Just sayin
- SketchCardsAndCovers
- Posts: 2
- Joined: Fri Jul 03, 2020 8:36 am
Re: Batgirl 3D print
Thanks! I'm thinking the same thing. Already have a guy on Facebook asking for a Green Hornet.
Cappy wrote: ↑Thu Mar 30, 2023 2:34 pm Those are great. I'm in. Actually if the stl's were available that would be preferred.
Saving up for an Elegoo Mars possibly Saturn resin printer. Be nice to print off the scale
I have a call for. Either way.
A series of "toonies" would awesome. As well as the 66 Batman series, there would most likely
be an interest in the Green Hornet, Kato and George Reeves Superman. Just sayin
Re: Batgirl 3D print
Since I don't have a printer, I'd like to know approximately what something like this might cost as a kit, please?
Larry